CLEANING BEDROOM
Preparing for Bed Making:
·
Remove
soiled bed linen from the bed.
·
Look
at the mattress pad / mattress protector to see if it is stained, torn or
damaged. If it is not straighten it and make sure the mattress and box spring
are even.
·
Always
adjust the mattress with your leg and not with your back to avoid any injuries.
·
If
the mattress pad is stained then remove it.
·
Get
a clean mattress pad and place it on the mattress:
·
Lay
the fresh pad on the bed.
·
Unfold
the pad right-side up and spread it evenly over the Centre of the bed.
·
Smooth
out any wrinkles.
·
Mattress
pads / mattress protector comes in different size, be sure to use the correct
size.
·
Make
sure you have the correct size sheets.
·
Do
not use a stained or torn sheet. Place them immediately in your solid linen
bag.
·
Take
three fresh sheets and 04 pillow cover / slips as per the bed size.
Making the bed:
·
Pull
the bed a little away from the headboard.
·
Spread
the 1st bed sheet and tuck the bottom side of the bed except for the four
corners.
·
Take
the loose end of the sheet, about a foot from the corner at the head of the bed
and pull it straight out, foaming a flap. Pull up the flap so it is flat.
·
Tuck
in the free part of the corner.
·
Pull
the flap out toward you and down over the side of the bed. Tuck the flap in.
·
Move
to the corner at the foot of the bed on the same side of the bed and repeat the
procedure.
·
Spread
the second sheet the wrong side up, from the edge of mattress.
·
Put
Quilt 6” lower than the 2nd sheet / blanket (quilt)
·
Spread
the third sheet over the quilt.
·
Fold
the second sheet above the quilt and the third sheet and make a fold
approximately 6” to 8”.
·
Tightly
tuck the sheets under the mattress.
·
Go
towards the foot of the bed and tightly tuck the second sheet, quilt and third
sheet together.
·
Maître
the corners.
·
Inset
the pillows into the new pillowcase and tuck in the loose ends.
·
Repeat
this process for the other pillows.
·
Place
the pillow on the bed with the tucked edges facing the centre and the tucked
flaps on the other side of the pillows.
·
Position
the bedspread on the bed with equal amounts hanging over both sides and the
foot of the bed.
·
Report
to the supervisor if you notice stains or tears in the bedspread.
·
Smooth
the bedspread over the pillows to the head of the bed.
·
Tuck
the remaining of the bedspread under the front edge of the pillows.
·
Smooth
the surface of the bed.
·
Check
the bedspread for evenness on both sides.
·
Push
back bed towards the side of headboard in the exact position.
·
All
the four corners of the bed is mitered properly. Bed linen is stain free and
properly pressed. Bed has to be firm.
·
Distance
of the pillow from Headboard to the fold of the bed is approximately 20”.
Mitter Corner
·
Lay
the sheet on the center of mattress
·
Let
the loose end fall over the side
·
Pick
up the mattress
·
Tuck
in the lower end part of the sheet all across the foot of the bed
·
Let
the sheet fall over the side
·
Pick
up the sheet from the bottom corner
·
Hold
the corner high to form a triangle
·
While
holding the triangle with one hand use other hand to from a neat corner
·
Rest
the triangle on the top end of the bed
·
With
the triangle still resting on the top of bed. Using both hands, tuck the
hanging part of sheet near the corner under the mattress
·
Pull
the triangle back and drop over the side
·
Now
tuck sheet under the mattress
·
Straighten
out the lines.
·
The
miter corner is completed
Miter is pronounced “My-ter”. Miter is the process of making a neat envelop fold of the sheets on the edges of the bed.
Source : Modul Housekeeping SIHI 2021
Jenis - Jenis Table Setting dan Cara Menset-Up Table Setting di Room Service Maupun BanquetTable se...
Read MoreCLEANING BEDROOMPreparing for Bed Making:· Remove ...
Read MoreSimple present tense adalah tenses yang digunakan ketika suatu kejadian sedang berlangsung saat i...
Read MoreCopyright ©2021 Subang International Hotel Institute